Etool buying guide
Choose by the material and operation, then the hole size. For screws and holes in wood or metal, start with a drill/driver. For mixed work including masonry, consider an impact drill such as the GSB 600 or GSB 183-LI. For a concrete-focused job or light chiselling, consider the SDS-plus GBH 220. These choices still depend on the exact tool's limits and the correct accessory. [1] [2] [3] [7]
Start with your job
- Furniture assembly and wood or metal holes: compare drill/drivers first. Bosch describes the GSR 185-LI for screwdriving in wood and drilling in wood and metal. See our GSR drill/driver comparison. [7]
- Mixed drilling with a suitable mains supply: the corded GSB 600 is a 600 W impact drill with published maximum diameters of 25 mm in wood, 10 mm in steel and 13 mm in masonry/concrete. [1]
- Screwdriving and mixed drilling without a cord: the 18 V GSB 183-LI offers a keyless chuck and screwdriving torque settings. Its published limits are 35 mm in wood and 10 mm in steel or masonry. [2]
- Concrete holes or light chiselling: the GBH 220 has an SDS-plus holder and separate drilling, hammer-drilling and chiselling modes. Bosch lists a 4–22 mm concrete drilling range; its manual identifies 6–12 mm for optimum drilling performance. [3] [6]
Maximum capacity is a limit, not a promise of speed, finish or suitability for every material condition. Describe the material, diameter, depth and number of holes before choosing a machine.
Questions buyers ask
1. Does “impact drill” mean the same as an impact driver?
Not here. The GSB 183-LI is a chuck-equipped drill/driver with an impact-drilling mode. Its manual separates drilling, screwdriving and impact drilling. Do not select a tool from the word “impact” alone; check the operation and accessory holder. [5]
2. Can the GSB 600 drill concrete?
Yes. Its manual includes concrete in intended use and specifies a 13 mm maximum concrete drilling diameter. That does not make it interchangeable with the GBH 220 for every concrete job. Check the hole and accessory requirements, rather than treating all wall materials alike. [4]
3. Can I buy the GSB 183-LI for reinforced concrete?
Do not infer reinforced-concrete approval from its 10 mm masonry rating. Its manual names brick, masonry and stone for impact drilling. Identify the concrete, reinforcement and job requirements before selecting the tool and bit; do not drill through reinforcement without the necessary approval. [5]
4. Does a 13 mm chuck mean I can drill 13 mm holes in everything?
No. The GSB 600 grips shanks from 1.5–13 mm, but its steel drilling limit is 10 mm. Match both the shank and the permitted hole diameter for your material. [1]
5. Can the GBH 220 take my ordinary wood and metal bits?
Only with the suitable chuck-and-SDS-plus-shank arrangement described in its manual, used without impact. Non-SDS-plus bits and their chucks must not be used for hammer drilling or chiselling. Do not assume that adapter or chuck is included. [6]
6. Which one can remove material with a chisel?
The GBH 220 is intended for light chiselling. The GSB models covered here do not offer a chiselling mode. Light chiselling is not a heavy-demolition rating. [4] [5] [6]
7. Should I choose corded or cordless?
Choose the required capacity first. The GSB 600 uses mains power; the GSB 183-LI uses the Bosch Professional 18 V system. For cordless buying, check the actual battery and charger in the selected offer. Neither a battery count nor a wattage figure guarantees a particular number of completed holes. [1] [2]
8. What should I check before drilling a wall?
Investigate hidden cables and pipes before drilling. Use suitable detection and seek utility assistance when needed. Read the full manual, secure the work, wear appropriate eye and hearing protection, and disconnect power before accessory changes. The GSB 600 and GBH 220 require their auxiliary handles; stop immediately if a bit jams. [4] [6]
View the Etool listings
- Bosch GSB 600 Professional Impact Drill
- Bosch GSB 183-LI one-battery listing
- Bosch GSB 183-LI two-battery listing
- Bosch GBH 220 SDS-plus Rotary Hammer
Check current price, availability, exact model and included equipment on the selected listing. A manufacturer variant's contents do not establish what a different store bundle contains.
Choose the next detail
Sources
Official Bosch India product pages and manufacturer instructions linked from them. Checked 25 October 2026. Follow the manual for the exact tool supplied.
- Bosch India: GSB 600, technical data.
- Bosch India: GSB 183-LI, technical data and applications.
- Bosch India: GBH 220, modes and drilling range.
- GSB 600 instructions, 1 609 92A 89B, printed pp. 5–8.
- GSB 183-LI instructions, 1 609 92A 9YR, printed pp. 5–9.
- GBH 220 instructions, 1 609 92A 5PG, printed pp. 6–10.
- Bosch India: GSR 185-LI, intended applications.